Selling the equipment
If you have surplus low-voltage switchgear in Maine, start with the equipment you can identify and the location where it is held. We are a buyer, not a seller: we review available details and can make a cash offer for a defined lot. We buy equipment across all voltage classes, pay the agreed amount upfront before pickup, and cover all freight for the purchased equipment. Offers depend on the specific equipment, condition, scope and other transaction details; an inquiry does not guarantee a purchase or a particular price.
For equipment we purchase, we handle and cover the entire removal and logistics process: our qualified crews isolate and disconnect it, and we arrange crane work when needed, rigging, loading, hauling and all freight. You do not have to disconnect, test, rig, load or haul the equipment. We coordinate the work with the authorized site contact and follow the site's applicable safety and access procedures.
Identify the low-voltage switchgear
Identify the rated voltage, main bus amperage, manufacturer, model or family, lineup section count and installed main and feeder breakers. If an existing one-line drawing shows a tie or multiple sources, include that information; it gives the buyer a better picture of the assembly than amperage alone.
Understanding the 240-volt description
For equipment described as 240 volts, distinguish the nameplate rating from the voltage of the system on which it was used. Phase, frequency, current and the installed protective devices are separate details. Include the location of the rating on the equipment or in existing records and note any uncertainty. We buy equipment across all voltage classes, not only the examples listed on this site; acceptance depends on the particular lot.
Condition and completeness
Explain whether breakers, door panels, control wiring and metering components are included and disclose visible corrosion or damage. A complete lineup may differ materially from a cabinet missing its main devices, so be clear about what is and is not included without removing any barriers.
Access and collection planning
Give the length, height and depth of the assembled lineup, and distinguish shipping sections if already documented. Note whether the equipment is in a basement, on an upper floor or at ground level, plus the path and doors leading to the agreed staging point.
Identify the building, equipment room, floor level and the practical route to a truck-accessible staging area. For occupied or shared premises, establish who controls the loading area, who can authorize release and whether an appointment is required. Explain any gate, weather, surface or security limitations that are known at the proposed collection date.
Build an inventory that can be checked
Give each item or lineup section a simple number, then list its manufacturer, description, accessible model or catalog number, voltage, current and quantity. For a mixed lot, say which loose components are included and where they are stored. A spreadsheet, equipment schedule or clear written list is sufficient; exact weights and perfect records are not a condition for starting the discussion. Mark uncertain details as unknown instead of estimating ratings. If several labels contradict the project paperwork, send both sources and identify which one belongs to the physical equipment. A clear inventory makes it easier to distinguish the offered assets from items that must remain on site.
Separate current rating from device details
The current rating on a main bus, the frame size of a circuit breaker and a breaker's trip rating are not necessarily the same. Voltage, phase, frequency, interrupting rating and configuration can matter too. Copy each rating with its label and unit when the information is already available, rather than reducing an entire assembly to one number. If devices have been replaced or the documentation conflicts with the visible label, explain the uncertainty. This is an inventory request, not an instruction to calculate a system rating or set protective devices. A buyer can begin reviewing incomplete information without seller-performed electrical testing.
Explain storage and exposure honestly
The useful history of surplus equipment is not limited to its age. Tell the buyer whether it has been stored indoors, outdoors, under cover or in an unconditioned building, and mention any known water, smoke, corrosion or physical damage. If a flood, process material or other environmental concern is known, describe it and share existing records when appropriate. A clean exterior does not establish the condition of internal parts, and an old date does not settle whether the equipment is usable. If you do not know the storage history, say so. There is no need to clean, open or operate equipment to make it appear more complete.
Electrical safety comes first
Electrical equipment can retain dangerous energy or remain connected to more than one source even when a project is described as shut down. Qualified personnel must isolate the equipment and establish its safe condition under the site's procedures before access, disconnection or removal. Do not open energized enclosures, remove barriers, rack breakers or touch exposed conductors to gather information. We do not ask sellers to energize or test equipment. Use existing records and photographs taken only where safely accessible; if a detail cannot be obtained safely, tell us it is unknown.
Cash offer, upfront payment and full-service removal
To request a cash offer for low-voltage switchgear, share the location, the quantity, the information available from existing records or safely accessible labels, and any known damage or missing parts. Include photographs only when they can be taken safely and are permitted by the site. Tell us when the equipment may be released and whether the lot includes related devices or documentation. If something is unknown, say so; no seller-performed electrical testing is needed.
We review the details and discuss an offer when the equipment and transaction are a fit. If an offer is agreed, we pay the agreed amount upfront before pickup. We arrange and cover qualified isolation and disconnects, crane work when needed, rigging, loading, hauling and all freight for the purchased equipment. The seller does not have to perform or arrange this work. Our crews coordinate access and the safe removal plan with the authorized site contact. There is no promise of a particular offer, acceptance or collection date.