Selling the equipment
If you have surplus low-voltage switchgear in Maine, start with the equipment you can identify and the location where it is held. We are a buyer, not a seller: we review available details and can make a cash offer for a defined lot. We buy equipment across all voltage classes, pay the agreed amount upfront before pickup, and cover all freight for the purchased equipment. Offers depend on the specific equipment, condition, scope and other transaction details; an inquiry does not guarantee a purchase or a particular price.
For equipment we purchase, we handle and cover the entire removal and logistics process: our qualified crews isolate and disconnect it, and we arrange crane work when needed, rigging, loading, hauling and all freight. You do not have to disconnect, test, rig, load or haul the equipment. We coordinate the work with the authorized site contact and follow the site's applicable safety and access procedures.
Identify the low-voltage switchgear
Identify the rated voltage, main bus amperage, manufacturer, model or family, lineup section count and installed main and feeder breakers. If an existing one-line drawing shows a tie or multiple sources, include that information; it gives the buyer a better picture of the assembly than amperage alone.
Understanding the 277/480-volt description
For a 277/480-volt system, provide the rated voltage, phase, frequency and main bus current from existing information. The equipment's protective devices and interrupting rating, when documented, are relevant in addition to the nominal system voltage. Include the location of the rating on the equipment or in existing records and note any uncertainty. We buy equipment across all voltage classes, not only the examples listed on this site; acceptance depends on the particular lot.
Condition and completeness
Explain whether breakers, door panels, control wiring and metering components are included and disclose visible corrosion or damage. A complete lineup may differ materially from a cabinet missing its main devices, so be clear about what is and is not included without removing any barriers.
Access and collection planning
Give the length, height and depth of the assembled lineup, and distinguish shipping sections if already documented. Note whether the equipment is in a basement, on an upper floor or at ground level, plus the path and doors leading to the agreed staging point.
Identify the building, equipment room, floor level and the practical route to a truck-accessible staging area. For occupied or shared premises, establish who controls the loading area, who can authorize release and whether an appointment is required. Explain any gate, weather, surface or security limitations that are known at the proposed collection date.
Keep spare parts tied to the right assembly
Spare breakers, removable units, relays, covers and manuals may be stored away from their original assembly. When they are included in a proposed sale, list each group separately and say which equipment it is believed to match. Preserve any existing part numbers or tags, but do not assert compatibility merely because two pieces look alike or carry a similar brand. Missing spares are not a reason to delay an initial inquiry. Conversely, if site personnel intend to keep certain spares for equipment still in service, state that clearly so those items are not accidentally counted in the offer or freight plan.
Identify the owner and the release contact
The person operating a building is not always the owner of its electrical equipment. A landlord, tenant, contractor, lender or other party may have an interest in some or all of the assets. Confirm who is authorized to sell the specific equipment and who will be available to release it to the carrier. If a demolition contractor is involved, clarify whether the contractor is merely removing the equipment or also owns it. For multiple sites, provide an appropriate contact at each location. Clear authority and accurate lot boundaries make the transaction simpler without requiring a seller to disclose unrelated confidential project information.
Explain storage and exposure honestly
The useful history of surplus equipment is not limited to its age. Tell the buyer whether it has been stored indoors, outdoors, under cover or in an unconditioned building, and mention any known water, smoke, corrosion or physical damage. If a flood, process material or other environmental concern is known, describe it and share existing records when appropriate. A clean exterior does not establish the condition of internal parts, and an old date does not settle whether the equipment is usable. If you do not know the storage history, say so. There is no need to clean, open or operate equipment to make it appear more complete.
Electrical safety comes first
A closed facility or idle machine does not by itself prove an electrical assembly is safe to handle. Our qualified crews coordinate with the authorized site team to isolate all applicable sources and establish a safe condition before disconnecting or moving equipment. Never operate a switch, remove a cover or expose live parts for a photograph or quote. Seller testing is not required, including operational, insulation or transfer testing. Existing nameplates and project records are useful where safely available, and an unknown rating can simply be listed as unknown.
Cash offer, upfront payment and full-service removal
To request a cash offer for low-voltage switchgear, share the location, the quantity, the information available from existing records or safely accessible labels, and any known damage or missing parts. Include photographs only when they can be taken safely and are permitted by the site. Tell us when the equipment may be released and whether the lot includes related devices or documentation. If something is unknown, say so; no seller-performed electrical testing is needed.
We review the details and discuss an offer when the equipment and transaction are a fit. If an offer is agreed, we pay the agreed amount upfront before pickup. We arrange and cover qualified isolation and disconnects, crane work when needed, rigging, loading, hauling and all freight for the purchased equipment. The seller does not have to perform or arrange this work. Our crews coordinate access and the safe removal plan with the authorized site contact. There is no promise of a particular offer, acceptance or collection date.